J. Dent. Ass. S. Afr. Vol. 31, No 10 pp 509-513 The Effects of the Acid Etch and Direct Bonding Technique in Orthodontics on Enamel Surface Topography P L Sadowsky and D H Retief Department of Orthodontics, University of the Witwatersrand, Johannesburg and Dental Research Unit of the South African Medical Research Council and the University of the Witwatersrand, Johannesburg, Republic of South Africa. SUMMARY The acid etch technique and the direct bonding of orthodontic attachments have become accepted procedures in clinical orthodontics. Changes are produced in enamel surface topography by acid etching and on removal of the bonded attachments at the end of treatment. These changes were examined by scanning electron microscopy and the clinical im­ plications of these surface changes are discussed. OPSOMMING In Ortodonsie word die suur-etstegniek en die direkte binding van aanhegtings aan tande as aanvaarbare kliniese prosedures beskou. Suur-etsing, sowel as die verwydering van die aanhegtings na afloop van die behandeling, veroorsaak veranderings in die oppervlaktopografie van glasuur. Hierdie verande­ rings is deur aftaselektronmikroskopie ondersoek en die kliniese implikasies van die waarnemings word bespreek. INTRODUCTION The added retention afforded by the acid etch technique has made the direct bonding of orthodontic attachments (Fig. 1) an accepted adjunct in the arma­ mentarium of the orthodontist (Zachrisson, 1975; Retief and Sadowsky, 1975). Several resin systems have recently become commercially available for the direct bonding of plastic and metal attachments and different techniques have been developed for the placement of the brackets. These all rely on prior etching of the enamel surfaces onto which the orthodontic attachments are to be bonded. The purpose of this investigation was to study the effects of an etching solution on human enamel sur­ faces and of polishing procedures on etched surfaces. In addition, clinical procedures to restore enamel sur­ faces after removal of bonded attachments were evaluated. MATERIALS AND METHODS Freshly extracted, sound human teeth were used in this investigation. The teeth were cleaned and stored at -4°C until needed. Some of the teeth were not etched in order to study normal enamel surfaces. The enamel surfaces of a number of teeth were etched with 50 percent phosphoric acid for two minutes. Some of the etched surfaces were polished with a rubber cup and a water slurry of pumice for varying time periods. Orthodontic attachments were bonded to some of the etched enamel surfaces under simulated clinical conditions. After allowing the resin to cure for approximately one Fig. 1. Directly bonded orthodontic attachments. hour, the bonded attachments were removed by hand instruments. Visible remnants of bonding material were removed with a dental scaler and the surfaces of some of these teeth polished with a rubber cup and a water slurry of pumice. A number of these polished surfaces were re-etched for two minutes with the 50 per cent phosphoric acid solution. Specimens from each of these groups were mounted on aluminium stubs and coated with silver in a high vacuum evaporator*. They were subsequently viewed in a Cambridge S4 Stereoscan scanning electron microscope**. The machine was operated at 15 kV and * Edwards Coating Unit, Edwards High Vacuum Ltd., Crawley, Sussex, England. ** Cambridge Scientific Instruments Ltd., Cambridge, England. Journal of the D.A.S.A. - October 1976 509 P L Sadowsky and D H Retief Fig. 2 Sound human enamel. SEM X 2000. Fig. 3. Human enamel etched with 50% phosphoric acid for 2 minutes. SEM X 2000. Fig. 4. Etched enamel mechanically polished for approximate­ ly 2 seconds. SEM X 2000. Fi*- S. Etched enamel mechanically polished for approximate­ ly 10 seconds. SEM X 2000. 510 Tydskrif van die T.V.S.A- - Oktober 1976 ENAMEL SURFACE TOPOGRAPHY Fig. 6. An enamel surface from which a bonded attachment had been removed and the remaining resin removed by scaling. SEM X 2000. Fig. 7. Mechanical polishing for approximately 2 seconds of the hand scaled enamel surface after bond removal. SEM X 2000. Fig■ 8 Mechanical polishing for approximately 10 seconds of the hand scaled enamel surface after bond removal. SEM X 2000. Fig. 9. The enamel appearance after bond removal, hand scal­ ing, mechanical polishing and subsequent phosphoric acid re-etching for 2 minutes. SEM X 2000. Journal of the D.A.S.A. - October 1976 511 P L Sadowsky and D H Retief the beam-specimen angle varied to obtain the best surface projection. RESULTS A normal enamel surface has a relatively featureless topography (Fig. 2). An enamel surface which had been etched with 50 per cent phosphoric acid for two minutes showed the preferential etching action of the acid. The prism cores were etched to a greater extent than the prism peripheries (Fig. 3). Figures 4 and 5 are scanning electron micrographs of etched enamel sur­ faces that had been polished with a rubber cup and pumice for varying lengths of time. The former was polished for approximately two seconds (Fig. 4) while the latter was polished for about 10 seconds (Fig. 5). A smoother surface topography was obtained by polish­ ing for a longer period. The surfaces of the teeth from which the bonded at­ tachments were removed and the visible resin rem­ nants scraped by means of scaling instruments, show­ ed that the normal enamel surface topography was obscured by adhering resin (Fig. 6). An appreciable amount of resin was left after polishing these surfaces with a rubber cup and pumice for two seconds (Fig. 7). Polishing for 10 seconds resulted in a smoother sur­ face (Fig. 8). Fig. 9 is a scanning electron micrograph o f an enamel surface from which the bonded attachments were removed, the enamel surface scaled and polish­ ed and then re-etched with 50 per cent phosphoric acid for two minutes. The exposed enamel surface has been etched but the bulk of the surface was covered by resin remnants which formed a protective coating against the acid attack. DISCUSSION The preferential etching of the enamel surface by 50 per i ent phosphoric acid produces micropores into which the curing bonding resin will flow. When cured the bonded attachments are mechanically retained to the etched surface (Gwinnett and Matsui, 1967). Etching of the enamel surface leads to a permanent loss of superficial enamel. The depth of etch or amount of enamel lost is dependent on the acid con­ centration and the duration, of etch (Silverstone, 1974; Retief, 1975). Etched enamel surfaces can readily be restored to their normal appearance by simple polishing procedures (Figs. 4 and 5). This confirms the observations previously reported by Newman and Facq (1971). In vitro studies by Lenz and Miihlemann (1963) of etched enamel surfaces suggested that the disappearance of the etching pattern could be due to abrasion or remineralization of the etched surfaces. Scanning electron microscope examinations of the in vivo recovery of etched enamel surfaces showed that apparent recovery of the etched surfaces had taken place (Lee et al, 1970; Retief, 1973). These studies did not prove that remineralization of etched enamel sur­ faces had occurred. Wei (1970) showed by electron microprobe x-ray spectrophotometry that etched sur­ faces were remineralized in vitro. Lee et al (1972) used a similar analytical technique to demonstrate that complete remineralization of etched enamel surfaces occurred in vivo. When directly bonded attachments were removed at the completion of orthodontic treatment, scaling with hand instruments alone to remove the visible rem­ nants of the bonding resin was not sufficient to produce a smooth enamel surface (Fig. 6). Further polishing with a rubber cup and pumice was required to produce an acceptable enamel surface topography (Fig. 8). The latter step is necessary to reduce plaque and debris accumulation. The time of mechanical polishing required will depend on the abrasive pro­ perties of the pumice used, the hand pressure applied and the hardness or abrasion resistance of the bon­ ding material. It has been shown clinically that rebonding after loss of a bonded attachment is possible (Retief and Sadowsky, 1975). This is probably due to the inflow of the bonding resin into the micropores created on a re­ etched surface (Fig. 9) and chemical union between the new resin and the resin entrapped in the etched enamel surface after failure of a bond. Concern has been expressed about the acid etch technique predisposing the enamel surface to carious attack after removal of bonded attachments. It has been shown that when the bulk of dental resins was removed from etched enamel surfaces, the materials which had penetrated the etched surfaces remained in situ (Gwinnett, 1971; Miura, Nakagawa and Ishizaki, 1973; Retief, 1974). Experiments carried out in vitro have demonstrated that the encapsulation of enamel crystallites by the resins which remained embedded within the etched enamel resulted in increased resis­ tance to subsequent demineralization (Gwinnett and Matsui, 1967; Silverstone, 1974). ACKNOWLEDGEMENTS We wish to thank the staff of the Electron Microscope Unit of the University of the Witwatersrand for their assistance with the scanning electron microscopy, the staff of the Dental Research Unit for printing the photomicrographs and Miss B. Slack for typing the manuscript. REFERENCES Gwinnett, A.J. (1971) Morphology of the interface between adhe­ sive resins and treated human enamel fissures as seen by scan­ ning electron microscopy. Archives of Oral Biology, 16, 237- 238. Gwinnett, A.J. & Matsui, A. (1967) A study of enamel adhesives. The physical relationship between enamel and adhesive. Archives of Oral Biology, 12, 1615-1620. Lee, H. et al. (1970) Application of scanning electron microscopy to in vivo remineralization studies of human enamel. Epoxylite Corporation Research Report, 70-147, 1-6. Lee, H.L. et al. (1972) Sealing of developmental pits and fissures: IV. Measurement of in vivo fluoride pickup by electron 512 Tydskrif van die T.V.S.A. - Oktober 1976 ENAMEL SURFACE TOPOGRAPHY microprobe x-ray spectrophotometry. Journal of Dental Re­ search, 51, 634-639. Lenz, H. & Miihlemann, H.R. (1973) In-vivo and in-vitro effects of saliva on etched or mechanically marked enamel after certain periods of time. Helvetica Odontologica Acta, 7, 30-33. Miura, F., Nakagawa, K. & Ishizaki, A. (1973) Scanning electron microscopic studies on the direct bonding systems. The Bulle­ tin of Tokyo Medical and Dental University, 20, 245-251. Newman. G.V. and Facq, J.M. (1971) The effects of adhesive systems on tooth surfaces. American Journal of Orthodontics, 59, 67-75. Retief, D.H. (1973) Effect of conditioning the enamel surface with phosphoric acid. Journal of Dental Research, 52, 333-341. Retief, D.H. (1974) Failure at the dental adhesive-etched enamel interface. Journal of Oral Rehabilitation, 1, 265-284. Retief, D.H. (1975) The use of 50 per cent phosphoric acid as an etching agent in orthodontics: A rational approach. American Journal of Orthodontics, 68, 165-178. k Retief, D.H. & Sadowsky, P.L. (1975) Clinical experience with the acid etch technique in orthodontics. American Journal of Ortho­ dontics, 68, 645-654. Silverstone, L.M. (1974) Fissure sealants. Laboratory studies. Caries Research, 8, 2-26. Wei, S.H.Y. (1970) Electron microprobe analysis of the remine­ ralization of enamel. Journal of Dental Research, 49, 621-625. Zachrisson, B.U. (1975) The acid etch technique in orthodontics. In: Proceedings of an International Symposium on The Acid Etch Technique, eds. Silverstone, L.M. & Dogon, I.L. pp. 265- 275. St. Paul, Minnesota: North Central Publishing Co. Journal of the D.A.S.A. - October 1976 513